Audi Q5 Owners & Service Manuals

Audi Q5: Steering Wheel

Overview - Steering Wheel

Audi Q5. Overview - Steering Wheel

1 - Airbag Spiral Spring/Return Spring with Slip Ring -F138-

  • Removing and installing. Refer to → Electrical Equipment; Rep. Gr.94; Steering Column Switch Module; Steering Column Switch Module, Removing and Installing.

2 - Steering Wheel

  • Removing and installing. Refer to → Chapter "Steering Wheel, Removing and Installing"

3 - Bolt

  • 30 Nm +90º
  • Always replace if removed

4 - Connector

5 - Connector

6 - Driver Side Airbag

  • Removing and Installing. Refer to → Body Interior; Rep. Gr.69; Driver Side Airbag; Airbag Unit with Igniter, Removing and Installing.

  WARNING

Follow the safety precautions when working on airbags. Refer to → Rep. Gr.00; Safety Precautions; Pyrotechnic Components Safety Precautions.

7 - Bolt

  • 7 Nm

8 - Cap

Steering Wheel, Removing and Installing

Special tools and workshop equipment required

  • Steering Wheel Scales -VAS6458-

Removing

  Note

  • Applies to vehicles equipped with dynamic steering:
  • Before the steering wheel can be removed from the steering column, the steering wheel must be in the exact horizontal using the Steering Wheel Scales -VAS6458-. Mount the new steering wheel so that it is horizontal using the Steering Wheel Level -VAS6458-.
  • After doing this step, the Steering Angle Sensor -G85- for setting the steering wheel position must be checked. While doing this, select the appropriate measured values block in the Steering Column Electronics Control Module -J527- in on board diagnostics. If the displayed value is > 0.5º, then the Steering Angle Sensor -G85- must be calibrated again and the dynamic steering must be adapted. Select the program in Guided Fault Finding. Refer to → Chapter "Dynamic Steering Basic Setting".

- Bring wheels in the straight position.

- Position steering wheel as far back as possible. Use entire steering column adjustment range to do this.

- Remove the airbag unit. Refer to → Body Interior; Rep. Gr.69; Driver Side Airbag; Airbag Unit with Igniter, Removing and Installing.

  Note

Removal and installation of steering wheel must take place in center position (wheels in straight-ahead position).

- Remove the bolt -2-.

- Mark position of steering wheel/column with a felt-tip pen.

- Remove steering wheel -3- from steering column.

Audi Q5. A69-0458

Installing

Install in reverse order of removal. Note the following:

Before positioning steering wheel, make sure wheels are in straight position.

- When installing a removed steering wheel, ensure that the markings on the steering column/steering wheel are aligned.

- When installing a new steering wheel (without a marking): mount the steering wheel in its center position (the steering wheel spokes must be horizontal and the wheels must be in the straight-ahead position).

- Install steering wheel.

- Install the airbag unit. Refer to → Body Interior; Rep. Gr.69; Driver Side Airbag; Airbag Unit with Igniter, Removing and Installing.

- Perform a road test.

- If steering wheel is crooked, remove it again and rotate it on steering column splines.

    READ NEXT:

     Overview - Steering Column

    1 - Bolt Tightening specification. Refer to → Body Interior; Rep. Gr.70; Instrument Panel Central Tube; Overview - Instrument Panel Central Tube. 2 - Bracket

     Steering Intermediate Shaft, Removing and Installing

    Special tools and workshop equipment required Torque Wrench 1331 5-50Nm -VAG1331- Removing - Bring wheels in the straight position. - Position the steering wheel as far down as possible

     Steering Column, Removing and Installing

    Special tools and workshop equipment required Torque Wrench 1331 5-50Nm -VAG1331-   WARNING Note the following before removing the steering column: Create a sketch showing the: routing o

    SEE MORE:

     Proper seating position for the front passenger

    The proper front passenger seating position is important for safe, relaxed driving. For your own safety and to reduce the risk of injury in the event of an accident, we recommend that you adjust the seat for the front passenger to the following position: Adjust the angle of the seatback so that

     Unfastening safety belts

    Unbuckle the safety belt with the red release button only after the vehicle has stopped. Fig. 163 Releasing the tongue from the buckle Push the red release button on the buckle > fig. 163. The belt tongue will spring out of the buckle. Let the belt wind up on the retractor as you guide the

    © 2019-2024 Copyright www.audiq5.net