Audi Q5 Owners & Service Manuals

Audi Q5: Overview - Lower Rear Lid Trim Panel

Audi Q5. Overview - Lower Rear Lid Trim Panel

1 - Bolt

  • Quantity: 4
  • 2 Nm

2 - Rubber Buffer

  • Quantity: 4
  • Insert in the trim panel

3 - Bracket

  • Quantity: 12
  • Insert in the trim panel
  • Replace if damaged or deformed
  • Remove the clips that are still in the mounting points on the body using the Omega Clip Tool -T40280-.

4 - Lower Trim

  • For the rear lid
  • Removing and installing. Refer to → Chapter "Lower Rear Lid Trim Panel, Removing and Installing".

5 - Cover

  • For tail lamps
  • Removing and installing. Refer to → Chapter "Tail Lamp Cover, Removing and Installing".

6 - Luggage Compartment Lamp

  • Removing and Installing. Refer to → Electrical Equipment; Rep. Gr.96; Lamps; Overview - Luggage Compartment Lamps.

7 - Cover

  • For the warning triangle
  • Removing and installing. Refer to → Chapter "Emergency Triangle Cover, Removing and Installing".

8 - Cover

  • For the emergency release
  • Removing and installing. Refer to → Chapter "Rear Lid Emergency Release Cover, Removing and Installing".

9 - Trim Panel

  • For rear lid lock
  • Removing and installing. Refer to → Chapter "Rear Lid Lock Trim, Removing and Installing".

10 - Rear Lid Lock Button In Luggage Compartment -E406-

  • Removing and installing. Refer to → Electrical Equipment; Rep. Gr.96; Controls; Rear Lid Lock Button in Luggage Compartment E406, Removing and Installing.

Overview - Upper Rear Lid Trim Panel

Audi Q5. Overview - Upper Rear Lid Trim Panel

1 - Upper trim

  • For the rear lid
  • Removing and installing. Refer to → Chapter "Upper Rear Lid Trim Panel, Removing and Installing".

2 - Bracket

  • Quantity: 8
  • Insert in the trim panel
  • Replace if damaged or deformed
  • Remove the clips that are still in the mounting points on the body using the Omega Clip Tool -T40280-.

3 - Rubber Buffer

  • Quantity: 11
  • Insert in the trim panel

Overview - Lock Carrier Trim

Audi Q5. Overview - Lock Carrier Trim

1 - Centering Pins

2 - Bracket

  • Quantity: 4
  • Insert in the trim panel
  • Replace if damaged or deformed
  • Remove the clips that are still in the mounting points on the body using the Omega Clip Tool -T40280-.

3 - Rear Lid End Trim Panel

  • With Rear Lid -Closed- Sensor 1 -G525- and Rear Lid -Closed- Sensor 2 -G526-
  • Removing and installing. Refer to → Chapter "Lock Carrier Trim, Removing and Installing, Non-Hybrid Vehicles".

    READ NEXT:

     Lower Rear Lid Trim Panel, Removing and Installing

    Special tools and workshop equipment required Pry Lever -80 - 200- Omega Clip Tool -T40280-, is needed to remove any clips are that still inside the body. Removing - Remove the luggage comp

     Luggage Compartment Side Trim Panel, Removing and Installing

    Special tools and workshop equipment required Pry Lever -80 - 200- Trim Removal Wedge -3409- Omega Clip Tool -T40280-, is needed to remove any clips are that still inside the body. Removing -&n

     Luggage Compartment Floor Covering Bracket, Removing and Installing

    Luggage Compartment Floor Covering Bracket, Removing and Installing, Front Bracket Removing Non-hybrid vehicles: - Remove the gap cover. Refer to → Chapter "Gap Cover, Removing and Insta

    SEE MORE:

     Connector Assignments

    Sound System Connector Assignments Standard, CAN Digital Sound System Control Module -J525- A - Black 32-pin connector (T32h)   Note Unlisted connector terminals are not assigned. A - Black 32-pin connector (T32h) 1 - Terminal 30 2 - Terminal 31 3 - Sub

     Door Handle, Removing and Installing

    Removing - Press the door outer seal to the side and remove the protective film over the hole -arrow A-. - Remove the locking bolt -4- as far as the stop using a screwdriver -1-. - Pull the exterior door handle and hold it in the "opened" position. - Press the housing retainin

    © 2019-2024 Copyright www.audiq5.net