Audi Q5 Owners & Service Manuals

Audi Q5: Battery Charger -VAS5095A- Support Mode

General Information

The support mode provides the vehicle electrical system with voltage when the Battery -A- is removed or disconnected.

For more information. Refer to the Battery Charger -VAS5095A- Operating Instructions.

The support mode is used for the following situations:

  • Vehicle electrical system support mode with the Battery -A- not installed
  • Maintaining the voltage when the battery is being replaced
  • Systems test without the Battery -A-

  WARNING

Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions".

  WARNING

Do not check or charge a Battery -A- when the visual indicator has "no color or is bright yellow". Jump starting must not be used!

There is a risk of explosion during testing, charging or jump starting.

These Batteries -A- must be replaced.

Special tools and workshop equipment required

  • Battery Charger -VAS5095A-

Procedure

  Caution

  • The polarity protection of the charger clamps is not active in the operation mode "charging severely discharged batteries/Support mode". Connect the charger clamps to the battery terminals correctly according to polarity!
  • It can result in sparks due to short circuit.
  • This constitutes an explosion risk.
  • Make sure the charging clamp connections are secure.

- Remove the Battery -A-. Refer to → Electrical Equipment; Rep. Gr.27; Battery; Battery, Removing and Installing.

  Caution

Whenever the Battery -A- is removed, be careful to prevent contact between the connected charge clamp on the positive terminal and the body ground. Likewise prevent contact between the battery terminals.

- Clamp the red charging clamp (+) to the vehicle positive battery terminal.

  Note

On vehicles with a Start/Stop function and an installed Battery Monitoring Control Module -J367-, the black charge terminal (-) must be connected to the body ground. The Start/Stop system will malfunction when it is connected to the Battery -A- negative terminal.

- Attach the black charging clamp (-) to the vehicle battery negative terminal.

- Check the setting for the support mode/standard operation switch. Refer to → Chapter "Battery Charger -VAS5095A- Device Description". It must be set to "support mode".

- Check correct polarity connection of charger clamps.

- Switch on the Battery Charger -VAS5095A-. Refer to → Chapter "Battery Charger -VAS5095A- Device Description".

The Battery Charger -VAS5095A- starts the support mode.

End the Battery Support Mode

- Switch off the Battery Charger -VAS5095A-. Refer to → Chapter "Battery Charger -VAS5095A- Device Description".

- Remove the charging clamps from the battery terminals.

- Disconnect the Battery Charger -VAS5095A- from the power.

Battery Charger -VAS5095A- Maintenance Charging

  WARNING

Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions".

  WARNING

Do not check or charge a Battery -A- when the visual indicator has "no color or is bright yellow". Jump starting must not be used!

There is a risk of explosion during testing, charging or jump starting.

These Batteries -A- must be replaced.

In maintenance charging, the Battery Charger -VAS5095A- provides safe charging and preserves the charge of the Battery -A-.

Procedure

- Proceed as if charging the Battery -A-. Refer to → Chapter "Battery, Charging with Battery Charger -VAS5095A-".

If the Battery -A- is discharged by an electrical consumer during maintenance charging, the Battery Charger -VAS5095A- automatically supplies the appropriate charge.

Maintenance charging can be performed without time restrictions. The Battery -A- can be used constantly.

    READ NEXT:

     Battery Charger -VAS5900-

      WARNING Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions".   WARNING Do not check or charge a Battery -A

     Battery Charger -VAS5900- Service Charge

      WARNING Risk of injury. Follow all warning messages and safety precautions. Refer to → Chapter "Warnings and Safety Precautions".   Caution "Service charging" is not permitted

     Battery Charger -VAS5900- Support Mode

    General Information The support mode provides the vehicle electrical system with voltage when the Battery -A- is removed or disconnected. For more information. Refer to the Battery Charger -VAS5900-

    SEE MORE:

     Luggage Compartment Side Trim Panel, Removing and Installing

    Special tools and workshop equipment required Pry Lever -80 - 200- Trim Removal Wedge -3409- Omega Clip Tool -T40280-, is needed to remove any clips are that still inside the body. Removing - Versions with screen separator: Remove the screen separator. - Fold the backrest forward. -

     Turn signal and high beam lever

    The lever on the left side of the steering column is used to operate the turn signals and the high beam as well as the headlight flasher. Fig. 50 Turn signal and high beam lever The turn signal and high beam lever has the following functions: Turn signals Lift the lever up all the way > fig.

    © 2019-2024 Copyright www.audiq5.net