Audi Q5 Owners & Service Manuals

Audi Q5: Activating the convertible locking retractor

Audi Q5 Type 8R (2008 - 2017) Owner's Manual / Safety / Child safety / Activating the convertible locking retractor

Use the convertible locking retractor to secure a child restraint.

Always heed the child safety seat manufacturer's instructions when installing a child restraint in your vehicle. To activate the convertible locking retractor:

  • Place the child restraint on a seat, preferably on the rear seat.
  • Slowly pull the belt all the way out.
  • Route it around or through the child restraint belt path
  • Push the child safety seat down with your full weight to get the safety belt really tight.
  • Insert the belt tongue into the buckle for that seating position.
  • Guide the safety belt back into the retractor until the belt lies flat and snug on the child safety seat.
  • You should hear a "clicking" noise as the belt winds back into the inertia reel. Test the convertible locking retractor by pulling on the belt. You should no longer be able to pull the belt out of the retractor. The convertible locking retractor is now activated.
  • Make sure that the red release button is facing away from the child restraint so that it can be unbuckled quickly.
  • Pull on the belt to make sure the safety belt is properly tight and fastened so that the seat cannot move forward or sideways more than one inch (2.5 cm).

WARNING

  • Using the wrong child restraint or an improperly installed child restraint can cause serious personal injury or death in a crash.
  • Always make sure that the safety belt retractor is locked when installing a child safety seat. An unlocked safety belt retractor cannot hold the child safety seat in place during normal driving or in a crash.
  • Always buckle the child safety seat firmly in place even if a child is not sitting in it. A loose child safety seat can fly around during a sudden stop or in a crash.
  • Always make sure the seat backrest to which the child restraint is installed is in an upright position and securely latched into place and cannot fold forward. Otherwise, the seatback with the child safety seat attached to it could fly forward in the event of an accident or other emergency situation.
  • Always read and heed all WARNINGS whenever using a child restrained in a vehicle is being used. Special precautions apply when installing a child safety seat on the front passenger seat.

    READ NEXT:

     Deactivating the convertible locking retractor

    The convertible locking retractor for child restraints will be deactivated automatically when the belt is wound all the way back into the retractor. Press the red button on the safety belt buckle.

     LATCH system (Lower anchorages and tethers for children)

    Child Restraint System anchors and how are they related to child safety To provide a simpler and more practicable way to attach the child restraint on the vehicle seat. Federal regulations require sp

     Installing a child restraint with LATCH lower anchorages

    Whenever you install a child restraint always follow the child restraint manufacturer's instructions. Fig. 181 Lower anchorages: proper mounting Mounting Make sure the seatback of the rear seat ben

    SEE MORE:

     Boot, Removing and Installing

    Electromechanical Steering Gear Boot, Removing and Installing Special tools and workshop equipment required Torque Wrench 1331 5-50Nm -VAG1331- Torque Wrench 1332 40-200Nm -VAG1332- Torque Wrench 1332 Insert - Ring Wrench - 21mm -VAG1332/7- Hose Clip Pliers -VAG1921- Clamping Pliers -VAG1682A

     Refrigerant Circuit Complaints

    Possible Refrigerant Circuit Concerns Test Requirements Electrical Equipment, vacuum system and air duct fault-finding has not revealed any faults. Refer to Guided Fault Finding for the A/C system ("OBD" or "Guided Fault Finding for the A/C system"), → Wiring diagrams, Troubleshooting &

    © 2019-2024 Copyright www.audiq5.net